Rotary Shaft Seal, Design Code TCN, Inside Diameter 16 mm, Outside Diameter 26 mm, Overall Width 7 mm, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 140 psi, Number of Lips 2, System of Measurement Metric, Case Coating None.

Rotary Shaft Seal, Design Code TCN, Inside Diameter 90 mm, Outside Diameter 115 mm, Overall Width 13 mm, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 140 psi, Number of Lips 2, System of Measurement Metric, Case Coating None.

Rotary Shaft Seal, Design Code SC, Inside Diameter 48 mm, Outside Diameter 70 mm, Overall Width 10 mm, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 7 psi, Number of Lips 1, System of Measurement Metric, Case Coating None.

Rotary Shaft Seal, Design Code SC, Inside Diameter 19 mm, Outside Diameter 35 mm, Overall Width 8 mm, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 7 psi, Number of Lips 1, System of Measurement Metric, Case Coating None.

Rotary Shaft Seal, Design Code SCV, Inside Diameter 110 mm, Outside Diameter 130 mm, Overall Width 12 mm, Contact Type Contact Seal, Lip Material Fluoro Rubber, Maximum Pressure 10 psi, Number of Lips 1, System of Measurement Metric, Case Coating None, Maximum Surface Speed 999 mps, Seal Type Single Lip Seal.

Rotary Shaft Seal, Design Code TCV, Inside Diameter 16 mm, Outside Diameter 30 mm, Overall Width 7 mm, Contact Type Contact Seal, Lip Material Fluoro Rubber, Maximum Pressure 10 psi, Number of Lips 2, System of Measurement Metric, Case Coating None, Maximum Surface Speed 999 mps, Seal Type Lip Seal.

Rotary Shaft Seal, Design Code SC, Inside Diameter 15 mm, Outside Diameter 30 mm, Overall Width 7 mm, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 7 psi, Number of Lips 1, System of Measurement Metric, Case Coating None.

Rotary Shaft Seal, Design Code TC, Inside Diameter 17 mm, Outside Diameter 30 mm, Overall Width 8 mm, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 7 psi, Number of Lips 2, System of Measurement Metric, Case Coating None.

Rotary Shaft Seal, Design Code SC, Inside Diameter 47 mm, Outside Diameter 72 mm, Overall Width 10 mm, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 7 psi, Number of Lips 1, System of Measurement Metric, Case Coating None.

Rotary Shaft Seal, Design Code TC, Inside Diameter 26 mm, Outside Diameter 38 mm, Overall Width 5 mm, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 7 psi, Number of Lips 2, System of Measurement Metric, Case Coating None.

Rotary Shaft Seal, Design Code SB, Inside Diameter 25 mm, Outside Diameter 52 mm, Overall Width 8 mm, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 7 psi, Number of Lips 1, System of Measurement Metric, Case Coating None.

Rotary Shaft Seal, Design Code SA, Inside Diameter 100 mm, Outside Diameter 130 mm, Overall Width 15 mm, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 7 psi, Number of Lips 1, System of Measurement Metric, Case Coating None.

5 in, Overall Width 0.

75 in, Outside Diameter 2.

Rotary Shaft Seal, Design Code SC, Inside Diameter 3.

Rotary Shaft Seal, Design Code TCV, Inside Diameter 45 mm, Outside Diameter 72 mm, Overall Width 8 mm, Contact Type Contact Seal, Lip Material Fluoro Rubber, Maximum Pressure 10 psi, Number of Lips 2, System of Measurement Metric, Case Coating None, Maximum Surface Speed 999 mps, Seal Type Single Lip Seal.

Rotary Shaft Seal, Design Code TC, Inside Diameter 2.375 in, Contact Type Contact Seal, Lip Material Nitrile Rubber, Maximum Pressure 7 psi, Number of Lips 2, System of Measurement Inch, Case Coating None.

Roll Roll.Tape,Yel,Magnta Chevrons,4"x100 ft.

Five channel, 1-3/8 in 45 degree left.

Round Milling Insert, Inscribed Circle 5/8 in, RNPJ1605M0SMH, MH, Double Sided, 0 Degrees.

Replaceable Drill Tip, TiAlN.

00 mm, HSS-E, Black Oxide, Thread Length 21.00 mm, Thread Limit 6H, Class of Fit 6H, Thread Direction Right Hand, Number of Flutes 2.

5000 in., Carbide, TiAlN, Non-Coolant Through, Weldon Flat, Decimal Inch, 1.End Mill, 1 in Milling Dia.

00mm, ANSI Code VSM17D040Z04A32XD17L250, Compatible Hardware Insert Screw M4x0.Indexable Square Shoulder End Mill, VSM17 Series, High Speed Steel, 16.20mm Depth of Cut 32.7 x 8.

Spiral Point Tap, Thread Size #4-40, UNC, Overall Length 1 7/8 in, High Speed Steel, Right Hand, Thread Length 1/2 in, 75 Percent Thread Drill Size 2.20 mm, Thread Limit H3, Class of Fit JIS 2, Number of Flutes 2.

3 in, Arbor Dia.7874 in, Coolant Fed Coolant Through Cutting Dia.750" L Not Applicable, Depth of Cut 0.

Thread Forming Tap, Thread Size 1/2 In.

Grooving/Parting Insert,WMT-U-PH,Carbide Grooving Width 4.00mm, ANSI Code WMTS400M4P06PH, Chip-Breaker Code PH, Chip-Breaker Style On One Side, Clearance Angle 5 Degrees , Coating Process PVD.

Spiral Flute Tap, Thread Size 1/4 In.-20, UNC, Overall Length 2 1/2 in, HSS-E-PM, TiCN, Thread Length 7/16 in, 75 Percent Thread Drill Size #7, Thread Limit 3BX, Class of Fit 3BX, Thread Direction Right Hand, Number of Flutes 3.

Parting and Grooving Insert.