38 Dia X 34 Shank 4Flute Rougher Finisher HSCO Cobalt End Mill

Drill Bit Size Letter C Drill Point Angle Degrees 135 Drill Bit Material Cobalt Drill Bit FinishCoating Gold Finish Flute Type Spiral Flute Cutting Direction Right Hand Shank Type Straight Through Coolant No Taper length drills are designed for general purpose drilling where longer length is required Heavy duty 135Deg split point.

Mill Diameter Inch 716 Number of Flutes 2 Length of Cut Inch 1316 Material High Speed Steel Overall Length Inch 334 Shank Diameter Inch 12 FinishCoating Bright Single or Double End Double Helical flute on the nose radius Suitable for high efficiency copying process and cutting of die mold corner radius Regular length 2 helical flutes, ball end Double end with straight shank.

Reamer Diameter Decimal Inch 0293 Reamer Material High Speed Steel Shank Type Straight Flute Type Straight This high quality tool is designed for most standard reaming needs M2 High Speed Steel.

Drill Bit Size Inch 516 Drill Point Angle Degrees 135 Drill Bit Material Cobalt Drill Bit FinishCoating Gold Finish Flute Type Spiral Flute Cutting Direction Right Hand Shank Type Straight Through Coolant No Taper length drills are designed for general purpose drilling where longer length is required Heavy duty 135Deg split point Sizes over 12 furnished with notched point.

Drill Bit Size mm 017 Drill Point Angle Degrees 118 Drill Bit Material High Speed Steel Drill Bit FinishCoating Black Oxide Flute Type Spiral Cutting Direction Right Shank Type Straight Coolant Through No 118Deg point.

25.0mm Diameter x 25mm Shank 3-Flute Regular Length Blue Series Carbide End Mills For: End milling, Slotting, Sinking On: Steels, Cast Iron, Aluminum, Copper, Brass, Plastics, and Abrasive type materials.

Shank Type Taper Shank Taper Size HSK63A Hole Diameter Inch 1 Projection Decimal Inch 630 Nose Diameter Decimal Inch 173 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.

Mill Diameter Inch 38 Number of Flutes 4 Material Cobalt FinishCoating Bright Length of Cut Inch 34 Shank Diameter Inch 38 Overall Length Inch 212 Center Cutting Yes Tools are finishing end mills with chipbreakers Prevents chattering while achieving good chip control and high efficiency Centre cutting.

Shank Type Taper Shank Taper Size HSK63A Hole Diameter Inch 1 Projection Decimal Inch 630 Nose Diameter Decimal Inch 173 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.

Mill Diameter Inch 38 Number of Flutes 4 Material Cobalt FinishCoating Bright Length of Cut Inch 34 Shank Diameter Inch 38 Overall Length Inch 212 Center Cutting Yes Tools are finishing end mills with chipbreakers Prevents chattering while achieving good chip control and high efficiency Centre cutting.