12.0mm Diameter X 12mm Shank 2-Flute Stub Length Ball Nose Blue Series Carbide End Mills

. Silicone is vulnerable to mechanical wear and tear, water and steam over 250 degrees F (121 degrees C), aromatic hydrocarbons (benzene), chlorinated hydrocarbons (trichloroethylene), acids and bases, and hydrocarbon fuels.224 Silicone O-ring 70A Shore Red, -500 Pack It has good resistance to ozone, weather, detergent, salt water, engine and transmission oil, non-petroleum brake fluid, hydraulic fluids that resist fire, vegetable and animal oils, and high molecular weight chlorinated aromatic hydrocarbons.

010 Buna/NBR Nitrile O-Ring 70A Shore Black, -1000 Pack and is compatible for use with petroleum, HFA, HFB and HFC fluids, vegetable oil, alcohol, acids and aliphatic hydrocarbons.

ROYAL LUXE 011861 Oversized Damask Stripe Down & Feather Comforter, Ivory, King.

BLUE RIDGE 013417 400 TC Windowpane White Goose Down Comforter, Ivory,.

ROYAL LUXE 414101 Plush Down Alternative Throw Blanket, Khaki.

.

0mm Diameter x 12mm Shank 2-Flute Stub Length Ball Nose Blue Series Carbide End Mills Stub end mills are specifically designed for shallow milling, contour milling and slotting.12.

Shank Type Taper Shank Taper Size CAT50 Hole Diameter Inch 58 Projection Decimal Inch 630 Nose Diameter Decimal Inch 106 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.

0mm Diameter x 12mm Shank 2-Flute Stub Length Ball Nose Blue Series Carbide End Mills Stub end mills are specifically designed for shallow milling, contour milling and slotting.

Shank Type Taper Shank Taper Size CAT50 Hole Diameter Inch 58 Projection Decimal Inch 630 Nose Diameter Decimal Inch 106 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.