7 X 78 X 112 Bore HSS Staggered Tooth Milling Cutter

Mill Diameter Inch 716 End Type Corner Radius Corner Radius Decimal Inch 0015 Number of Flutes 2 Material Solid Carbide FinishCoating Bright Length of Cut Inch 1 Shank Diameter Inch 716 Overall Length Inch 234 Cutting Direction Right Variable Index No Special geometry allows for high chip loads and feed rates Excellent for slotting and profiling at high speeds Made from premium submicron grain carbide Cutting diameter tolerance 00000002.

Shank Type Taper Shank Taper Size CAT40 Hole Diameter mm 32 Projection mm 100 Nose Diameter mm 44 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.

Cutting Diameter Decimal Inch 492 Maximum Depth of Cut Decimal Inch 0197 Cutting Diameter mm 125 Arbor Hole Diameter Decimal Inch 15 Overall Height Decimal Inch 248 Series Mold Max Number of Cutter Inserts 7 Insert Compatibility RPMM 120400 Cutter Style MMFM 4125R High strength of Cutting Edge and Excellent Surface finish by R type inserts Outstanding efficiency in cutting performance with difficulttocut material of high degree of hardness Suitable to curved surface of moulds Economical cutter body assembling with Screw.

Sold As Pair Overall Length Inch 234 Overall Width Inch 134 Overall Height Inch 158 V Angle 90Deg This range of Vee blocks is made from finely selected tool steel fully hardened to 5560 HRC Manufactured and numbered in matched pairs, each pair has two 90Deg Vees of different capacities which are identical to the Vees of its matching block The Vee's are ground central, parallel and square with the ends and sides.

Hand of Holder Neutral Toolholder Style MTCNN Rake Angle 7Deg Shank Width Decimal Inch 075 Shank Height Decimal Inch 075 Overall Length Decimal Inch 45 Insert Compatibility TN 43.

Series Name 0 Diameter mm 155 Diameter Decimal Inch 06102 Series CodeSeat Size 0 Material Cobalt Coating TiN Thickness Inch 18 Included Angle 132 For drilling in High Alloy materials exotic materials, T15 may also be used in general purpose applications where increased speeds and enhanced wear resistance is required 132Deg point.

Connection Type Arbor Included Angle 60Deg Cutting Diameter Inch 3 Cutting Width Inch 58 Cutting Direction Left Material High Speed Steel FinishCoating Uncoated Arbor Hole Diameter Inch 1 45Deg and 60Deg angles High Speed Steel.

Cutter Diameter Inch 7 Cutting Width Inch 78 Tooth Configuration Staggered Material High Speed Steel FinishCoating Uncoated Arbor Hole Diameter Inch 112 Number of Teeth 26.

Connection Type Arbor Included Angle 60Deg Cutting Diameter Inch 3 Cutting Width Inch 58 Cutting Direction Left Material High Speed Steel FinishCoating Uncoated Arbor Hole Diameter Inch 1 45Deg and 60Deg angles High Speed Steel.

Cutter Diameter Inch 7 Cutting Width Inch 78 Tooth Configuration Staggered Material High Speed Steel FinishCoating Uncoated Arbor Hole Diameter Inch 112 Number of Teeth 26.