1 Dia X 1 Shank 4Flute Regular Length Double End HSCO Cobalt End Mill

Jaw Type: Square Material: Steel Jaw Interface Type: 3/32x90 degree Maximum Compatible Chuck Diameter mm: 500 Minimum Compatible Chuck Diameter mm: 400 Overall Height mm: 90 Groove Width mm: 25.5For AutoBlok, Erickson, Forkardt, Gamet, Powerhold, Pratt Burnerd, Rohm and Howa Ho12M-Self Contained Air.

Shank Type Taper Shank Taper Size HSK63A Hole Diameter Inch 34 Projection Decimal Inch 394 Nose Diameter Decimal Inch 13 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.

Insert Style: TPU Insert Size: 434 Material: Carbide Manufacturer's Grade: PTM30U Material Grade: C5, C5-C6.

On: Variety of Steels, Cast Iron, Non-Ferrous metals, Plastics, Abrasive type materials..

Collet System ER Collet Series ER16 Shank Type Taper Shank Taper Size CAT50 Projection Decimal Inch 412 DIN Coolant option standard All Ground Body Factory Balanced to save spindle life, tool life and increased productivity Threaded through holes for a backup screw tool stop or coolant through when removed Wrench not included Premium balanced to G25 At 30,000 rpm.

.

TiAlN coated for increased speed and feed capabilities and enhanced tool life.1/4" Diameter x 1/4" Shank 2-Flute Long Length Ball Nose Blue Series Carbide End Mills These end mills have the capability to mill much thicker material in a single pass, thereby eliminating the interrupted cut that may be present with regular length end mills.

Mill Diameter Inch 1 Number of Flutes 4 Material Cobalt Length of Cut Inch 178 Shank Diameter Inch 1 FinishCoating Bright Single or Double End Double Center Cutting Yes Overall Length Inch 638 Flute Direction Right Cutting Direction Right Variable Helix No Helix Angle 30 Double end economy Used for slabbing, shallow pocketing, tracer milling or die sinking and similar operations.

1/4" Diameter x 1/4" Shank 2-Flute Long Length Ball Nose Blue Series Carbide End Mills These end mills have the capability to mill much thicker material in a single pass, thereby eliminating the interrupted cut that may be present with regular length end mills. TiAlN coated for increased speed and feed capabilities and enhanced tool life.

Mill Diameter Inch 1 Number of Flutes 4 Material Cobalt Length of Cut Inch 178 Shank Diameter Inch 1 FinishCoating Bright Single or Double End Double Center Cutting Yes Overall Length Inch 638 Flute Direction Right Cutting Direction Right Variable Helix No Helix Angle 30 Double end economy Used for slabbing, shallow pocketing, tracer milling or die sinking and similar operations.