New Operators Manual Fits Allis Chalmers 14C

One New Aftermarket Manufacturer Part 100XL709PACKAGED UOM 1EACHTECHNICAL SPECIFICATIONS Brand DD Powerdrive, WidthThick 7080 Inch, Length 10 Inch, No Of Teeth 50, Material Neoprene, Series XL, Pitch 15 InchFEATURES BENE FitsFiberglass tensile cord through entire length for excellent flex life, superior torque capability and lower stretchTrapezoidal tooth profile made from nylon for longer service lifeSingle timing belts are made from Neoprene to provide protection against moisture, grease, grime and oilEliminates the need for lubrication and retensioningliliOil ResistantliliHeat ResistantliliAbrasion ResistantliliProvides a maintenance free, cost effective solution for every timing driveliul.

JAndN Electrical Products Jacketed Duplex Wire OF WIRES: 2, OPERATING TEMPERATURE: -30° to 105°C / -22° to 221°F, SPOOL LENGTH: 100mm, SPOOL LENGTH: 3.937, VOLTAGE RATING: 0-60, WIRE GAUGES: 12Replaces Part Numbers: 600-12013-100.

AAF1670J Filter, Air QTY 1.

AFTERMARKET 703883R7 Cylinder Head Gasket.

One New Aftermarket Tech InfoOther OEMS 37101P, 48500CENTER OF GROOVE TO REAR 0244, CENTER OF GROOVE TO REAR 6200mm, CRITICAL NOTE This is NOT an Alternator Pulley This is CrankGear Driven Off the Back of the Engine to Support the Power Steering, Air Conditioner, and Water Pump, GROOVE OD 2594, GROOVE OD 65900mm, GROOVE TYPE Serpentine, ID 0421, ID 10700 mm, NUMBER OF GROOVES 6, OD 2642, OD 67100 mm, PULLEY TYPE DecouplerReplaces Part Numbers 20624042.

AFTERMARKET ENU70-0092 RE531288 Turbocharger Fits John Deere 8225R 8245R 8270R.

The Operator Manual owner's manual for the Fits Allis Chalmers model 14C Crawler, is the manual that would have come with the machine when it was new This 76 page manual contains valuable information such as proper operation and preventative maintenance procedures Also included are the lubri Fits CATion points, fluid capacities, and minor adjustment information to things like the clutch, brakes, and carburetor Every owner of the Fits Allis Chalmers 14C Crawler needs this manualp.

375 Inch, Outside Length: 25 Inch, Manufacturer: DAndD PowerdriveFEATURES And BENE FitsExtra highly flexible neoprene backing provides excellent abrasion and wear resistanceBacking also guards the tensile cords against oil, grease, dirt and moistureBelts constructed with fiberglas tensile cords which quarantee diemensional stability to eliminate take up adjustmentsTeeth are oil and heat resistantNeoprene teeth have a shear resistance equal to the tensile strength of the beltTooth design provides a constant circular pitch to assure full surface contact between belt and pulley.

The Operator Manual owner's manual for the Fits Allis Chalmers model 14C Crawler, is the manual that would have come with the machine when it was new This 76 page manual contains valuable information such as proper operation and preventative maintenance procedures Also included are the lubri Fits CATion points, fluid capacities, and minor adjustment information to things like the clutch, brakes, and carburetor Every owner of the Fits Allis Chalmers 14C Crawler needs this manualp.

375 Inch, Outside Length: 25 Inch, Manufacturer: DAndD PowerdriveFEATURES And BENE FitsExtra highly flexible neoprene backing provides excellent abrasion and wear resistanceBacking also guards the tensile cords against oil, grease, dirt and moistureBelts constructed with fiberglas tensile cords which quarantee diemensional stability to eliminate take up adjustmentsTeeth are oil and heat resistantNeoprene teeth have a shear resistance equal to the tensile strength of the beltTooth design provides a constant circular pitch to assure full surface contact between belt and pulley.250XL037 DAndD Powerdrive Timing Belt Of Teeth: 125, Widths: .