1/4-20 UNC H.S.S. Taper Hand Taps

Drill Bit Size Inch 38 Drill Bit Material High Speed Steel Drill Point Angle Degrees 118 Drill Bit FinishCoating Black Oxide Overall Length Inch 18 Through Coolant No 118Deg point.

Tip Material Brazed Carbide Tip Material Grade C5 Tool Bit Type CutOff Tool Bit Style CTR11 Cutting Direction Right Hand Shank WidthDiameter Inch 1 Shank Height Inch 1 Overall Length Inch 5.

Collet System ER Collet Series ER20 Shank Type Taper Shank Taper Size CAT50 Projection Decimal Inch 12 DIN Coolant option standard All Ground Body Factory Balanced to save spindle life, tool life and increased productivity Threaded through holes for a backup screw tool stop or coolant through when removed Wrench not included Premium balanced to G25 At 30,000 rpm.

Mill Diameter Inch 12 Number of Flutes 4 Material High Speed Steel Length of Cut Inch 114 Shank Diameter Inch 12 FinishCoating Bright Single or Double End Single Center Cutting Yes Overall Length Inch 314 Flute Direction Right Cutting Direction Right Variable Helix No Helix Angle 30 Centre cutting allows these end mills to drill into the part for the beginning of a slot These centre cutting end mills are recommended for pocketing, tracer milling, cam milling, die sinking and slotting.

.1/8" Diameter x 1/8" Shank 4-Flute Long Length Ball Nose Blue Series Carbide End Mills These end mills have the capability to mill thicker material in one pass, eliminating the interrupted cut that may be present with regular length end mills.

Shank Type Taper Shank Taper Size CAT50 Hole Diameter Inch 34 Projection Decimal Inch 630 Nose Diameter Decimal Inch 13 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.

Mill Diameter Inch 34 Number of Flutes 4 Material High Speed Steel Length of Cut Inch 158 Shank Diameter Inch 34 FinishCoating Bright Single or Double End Single Center Cutting Yes Overall Length Inch 378 Flute Direction Right Cutting Direction Right Variable Helix No Helix Angle 30 Centre cutting allows these end mills to drill into the part for the beginning of a slot These centre cutting end mills are recommended for pocketing, tracer milling, cam milling, die sinking and slotting.

.

Mill Diameter Inch 34 Number of Flutes 4 Material High Speed Steel Length of Cut Inch 158 Shank Diameter Inch 34 FinishCoating Bright Single or Double End Single Center Cutting Yes Overall Length Inch 378 Flute Direction Right Cutting Direction Right Variable Helix No Helix Angle 30 Centre cutting allows these end mills to drill into the part for the beginning of a slot These centre cutting end mills are recommended for pocketing, tracer milling, cam milling, die sinking and slotting.

.High Speed Steel for hand tapping of through holes in ferrous and non-ferrous alloys.