1/4 Diameter X 1/4 Shank 2-Flute Stub Length Ball Nose Blue Series Carbide End Mills

.1/8" Diameter x 1/8" Shank 4-Flute Long Length Ball Nose Blue Series Carbide End Mills These end mills have the capability to mill thicker material in one pass, eliminating the interrupted cut that may be present with regular length end mills.

Shank Type Taper Shank Taper Size CAT50 Hole Diameter Inch 34 Projection Decimal Inch 630 Nose Diameter Decimal Inch 13 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.

Mill Diameter Inch 34 Number of Flutes 4 Material High Speed Steel Length of Cut Inch 158 Shank Diameter Inch 34 FinishCoating Bright Single or Double End Single Center Cutting Yes Overall Length Inch 378 Flute Direction Right Cutting Direction Right Variable Helix No Helix Angle 30 Centre cutting allows these end mills to drill into the part for the beginning of a slot These centre cutting end mills are recommended for pocketing, tracer milling, cam milling, die sinking and slotting.

.High Speed Steel for hand tapping of through holes in ferrous and non-ferrous alloys.

Type Taper Adapter Taper Adapter Type R8 To Jacobs Outside Taper Size R8 Inside Taper Size JT6 Through Coolant No Projection Decimal Inch 013 Hole Diameter Decimal Inch 0677.

Maximum Measurement mm 125 Maximum Measurement Inch 12 Maximum Measurement Decimal Inch 05 Resolution Decimal Inch 000005 Resolution mm 00001 Back Type Flat Back Lug Supplied The maximum, minimum, or runout value can be displayed during measurement Tolerance measurement feature allows for the upper and lower tolerance for maximum and minimum InchMetric and ABSINC conversion Flat back attached and lug back supplied Lug Back, Battery, Instruction manual.

1/4" Diameter x 1/4" Shank 2-Flute Stub Length Ball Nose Blue Series Carbide End Mills Stub end mills are specifically designed for shallow milling, contour milling and slotting.

Head Diameter Inch 114 Number of Flutes 6 Included Angle 82 Countersink Material High Speed Steel Countersink FinishCoating Black Oxide Shank Diameter Inch 12 Flutes are staggered to ensure smoother, chatterfree cutting action Steam black oxide surface treatment enhances tool life and prevents galling 100 CNC manufactured to tighter than industry standard tolerances.

1/4" Diameter x 1/4" Shank 2-Flute Stub Length Ball Nose Blue Series Carbide End Mills Stub end mills are specifically designed for shallow milling, contour milling and slotting.

Head Diameter Inch 114 Number of Flutes 6 Included Angle 82 Countersink Material High Speed Steel Countersink FinishCoating Black Oxide Shank Diameter Inch 12 Flutes are staggered to ensure smoother, chatterfree cutting action Steam black oxide surface treatment enhances tool life and prevents galling 100 CNC manufactured to tighter than industry standard tolerances.