E5 D Flat Tool Post Holder

Drill Bit Size Inch 118 Shank Taper Designation MT4 Drill Point Angle Degrees 118 Drill Bit Material Carbide Tipped Drill Bit FinishCoating Bright Overall Length Inch 1234 Through Coolant No Provides excellent wear resistance when cutting aluminum castings, bronze, cast and ductile irons, fiberglass, hard plastics and other nonferrous materials NOT recommended for steel applications 118Deg point.

Drill Blank Size Decimal Inch 012 Drill Blank Size Wire 31 Blank Length Inch 234 Made from hardened HRC 6365 high speed steel and ground, can be used as punches, gauges, pins or ground for special tools High Speed Steel 00000 00003.

Spring-loaded plunger expands within the bore (or groove), allowing determination of the internal diameter with a knurled clamp.

Head Diameter Inch 18 Number of Flutes 6 Included Angle 82 Countersink Material Solid Carbide Countersink FinishCoating Bright Shank Diameter Inch 18.

It can be widely used for boring, milling, drilling and tapping as well as for grinding operation, and is available for all sizes.4527) Collet This collet can clamp for a specific standard size and its next size..

Material High Speed Steel Blade Diameter Inch 234 Blade Thickness Decimal Inch 0036 Arbor Hole Diameter Inch 34 Connection Type Arbor Number of Teeth 72 High Speed Steel.

Shank Type Taper Shank Taper Size CAT50 Hole Diameter Inch 1 Projection Decimal Inch 394 Nose Diameter Decimal Inch 173 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.

Tool Post Holder Number D Tool Post Holder Type Turning Facing Holder Lathe Swing Inch 1018 Overall Length mm 100.

Shank Type Taper Shank Taper Size CAT50 Hole Diameter Inch 1 Projection Decimal Inch 394 Nose Diameter Decimal Inch 173 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.

Tool Post Holder Number D Tool Post Holder Type Turning Facing Holder Lathe Swing Inch 1018 Overall Length mm 100.